Clark's DJ Table · build guide · v1 (Bluetooth only) · updated Oct 9, 2026

Build guide

Print, assemble and wire the table, then test each part as it goes in. Every connection is listed on the Wiring page; this page is the order to do them in.

Firmware is the next piece of work. Stages A–E each get a small test sketch, so every stage can be checked before the next one is wired.

1Tools & parts

Full parts list: docs/bom.md in the repo. Hardware for the case: 4 Kadrick M3 × 5 heat-set inserts and 4 M3 × 8 button-head screws.

2Print the tray and top plate

PartFileOn the bed
Top platecad/print/plate_print.stltop face down on smooth PEI; posts point up
Traycad/print/tray.stlfloor down, open top up
  1. Settings (same as the Hammond panels): PLA, 0.2 mm layers, 4–5 walls, 15–20 % infill, 3 mm brim, no supports.
  2. Print both. The tray has no floor mounts in v1: the boards stick down with double-sided foam tape (positions on the Inside layout).

Check · A knob's encoder and a FILN button thread into their holes; the fader lever slides the full slot without rubbing.

3Heat-set inserts

  1. Iron at ~220 °C for PLA. Set an M3 × 5 insert on a corner post's hole, narrow end down.
  2. Press it in with the iron tip, gently and straight, until it's flush with the top of the post. Don't push past flush.
  3. Slide the iron out and let it cool for 10 seconds. Repeat for all four corners.

Check · Set the plate on the tray and thread all four M3 × 8 screws in by hand, then take them back out.

4Solder the DAC

  1. Practise first on one of the spare DAC boards.
  2. Check the four config pads on the back first (H1L–H4L, beside FLT, DEMP, XSMT, FMT). You want FLT L, DEMP L, XSMT H, FMT L. Boards ship with a tiny zero-ohm resistor joining each middle pad to one side; if one is on the wrong side, bridge its middle pad to the right side with a small blob.
  3. Iron: 245 handpiece, C245-2.4D chisel tip, 340 °C, 60/40 solder.
  4. The header goes in pins up: plastic on the component side, short ends through to the back, so the long pins stand up and take female–male jumpers.
  5. Turn the board over to solder the back. The LINE OUT jack is taller than the header's plastic, so prop the jack end level (an eraser or a scrap header strip) or tape the header down.
  6. Tack one end pin and check the header is square to the board; reheat that joint to straighten it if not. Then the other end pin, then the middle four.
  7. For each pin: iron on pad and pin together 1–2 s, feed solder into the joint, remove the solder, then the iron. Aim for small shiny cones.

Check · No solder bridges between neighbouring header pins (multimeter continuity between adjacent pins should be silent).

5Mount the top-plate parts

  1. Encoders (5): from below, push the bushing up through the hole, nut on top. Turn each so its pins point toward the back. Knobs on: black for LOW / MID / HIGH, orange for FILTER, the fifth for ECHO.
  2. Buttons: the three silver green-ring FILN buttons in the front row (PREV, PLAY, NEXT), the fourth at SOURCE. Nut on underneath.
  3. BT LED holder into the small hole beside SOURCE.
  4. OLED: glass into the window, board on the four posts under the plate, then 4 × M2 × 4 self-tapping screws from below into the posts. Snug, not tight; the glass should sit centred in the window.
  5. Fader: board under the slot, pin end toward the front, pins pointing toward the knobs. Four M3 × 6 screws up through the board into the posts. Press the cap on the lever from above.

Check · The fader slides end to end; every knob turns and clicks in when pushed; every button clicks.

6Mount the back-panel parts

  1. USB-B: two M3 screws and nuts through the flange holes.
  2. Antenna: RP-SMA bulkhead through its hole (rightmost seen from behind), washer and nut inside.
  3. Audio out: 3.5 mm panel-mount extension through its hole, nut inside.
  4. Optical and coax holes stay empty for now.

7Mount the floor boards

  1. Breadboard: peel its adhesive backing and press it down on the right side of the floor.
  2. ESP32 breakout: double-sided foam tape, back left; plug in the DevKitC, USB end toward the middle.
  3. MCP23017: foam tape at the back, under where the OLED will sit.
  4. DAC: double-sided tape (the board has no mounting holes), header pins up, LINE OUT jack facing the back. Place it where the jumpers reach the breadboard and the LINE OUT extension reaches the rear AUDIO OUT.
  5. Connect the USB cable from the USB-B mount to the DevKitC, and the antenna pigtail to the module's u.FL socket (press straight down until it clicks).

8Power rails & first power-on

  1. Run the breakout's 5V to the breadboard's top + rail, 3V3 to the bottom + rail, and GND to both − rails. Nothing else connected yet.
  2. Plug a USB charger into the rear USB-B.
  3. Measure each rail to GND.

Check · Top rail ~5.0 V, bottom rail ~3.3 V. If either is wrong, unplug and recheck before going on.

9Stage A · Bluetooth audio

  1. Unplug USB. Wire the DAC with six female–male jumpers: VIN, GND, SCK→GND, LCK→19, DIN→23, BCK→18 (table).
  2. Plug in the DAC's LINE OUT extension; connect the rear AUDIO OUT to the amp with a 3.5 mm → RCA cable. Amp volume low.
  3. Flash the Stage A sketch over the rear USB.
  4. On the phone, pair with Clark's DJ Table and play something.

Check · Music from the amp, clean and in stereo. This is the core of the table; everything after adds controls to it.

10Stage B · Fader

  1. Fader GND, VCC (3.3 V), OTA → GPIO 36 (table).
  2. Flash the Stage B sketch.

Check · Sliding the fader changes the volume smoothly from silent to full.

11Stage C · Buttons & LEDs

  1. Button switch wires: NO → 16 / 17 / 32 / 39, C → GND. Add the 10 kΩ pull-up on 39 (table).
  2. LED rings: + to 5 V, − of all three to the transistor's collector; base through 1 kΩ to GPIO 4; emitter to GND.
  3. BT LED: 330 Ω to GPIO 33, short leg to GND.
  4. Flash the Stage C sketch.

Check · PLAY pauses and resumes the phone, PREV / NEXT skip tracks, the green rings light, the BT LED shows the connection.

12Stage D · Screen

  1. OLED: VCC to 3.3 V (never 5 V), GND, SCL→14, SDA→13, RST→25, DC→26, CS→27 (table).
  2. Flash the Stage D sketch.

Check · Track title and artist from the phone show on the screen and change with the song.

13Stage E · Encoders

  1. Build the ten dividers on the breadboard: for each A and B line, 1 kΩ from the encoder wire to a node, 2 kΩ from the node to GND.
  2. Power the encoders: pin 1 → 5 V, pin 6 → GND, pin 5 → GND.
  3. Before connecting the MCP23017: power up, turn each knob slowly and measure each divider node.
  4. MCP23017: VCC to 3.3 V, GND, SDA→21, SCL→22, INTA→34. Then the nodes and push wires to their MCP pins; ECHO's push goes to GPIO 35 with a 10 kΩ pull-up (table).
  5. Flash the Stage E sketch.

Check · Each divider node swings 0 ↔ ~3.3 V while turning (not 5 V). Then: every knob moves its effect both ways, and pushing ECHO throws an echo.

14Close it up

  1. Tuck wires away from the fader board and the encoder pins; nothing should press on the breadboard.
  2. Lower the plate in, lip inside the walls, and drive the four M3 × 8 button-head screws.

Check · Run through stages A–E once more with the lid on.

15Troubleshooting

SymptomLook at
Pairs, but silenceDAC SCK not grounded; XSMT pad not set to H; LCK / BCK swapped
Loud hiss or distortionamp input set to phono instead of line; fader all the way up into a sensitive input
Knob turns the wrong wayswap its A and B in firmware
Knob jumps or skipsdivider values; add the 100 nF across the encoder's VDD/GND
Screen blankVCC on 3.3 V; CS / DC / RST on the right pins
LED rings darktransistor pin order (E·B·C vs C·B·E); + wires on 5 V
Won't boot after wiringsomething pulling GPIO 0, 2, 5, 12 or 15; disconnect the last change